10/5/2023 0 Comments Fiberglass pond shellView the liner or the outline from all angles – even from an upstairs window. If it’s to be a sunken pond, then mark its outline with a hosepipe or line and move the pond shell out of the way. To make sure that the site is right, place the liner in the chosen spot. It’s important to position the pond correctly the first time, unless you enjoy doing everything twice. Siting a pre-formed pond liner, and marking out For a raised pond – materials to hide the liner sides.ħ.Depth gauge – use a cane or stick marked with paint or tape.Builder’s spirit level plus a straight piece of wood that is slightly longer than the length of the liner.Essential tools/materials before you start: It’s also preferable to have none of the liner exposed to sunlight – so keep the water level topped up and shade the top with edging stones or overhanging plants. This is very difficult to disguise and it’s far better to ensure that the liner is correctly placed to start with. If you install a liner on the slant, the water level will be a permanent reminder of your mistake, with water full to the brim on one side of the pond and exposing the liner on the other. This is because it’s essential to position them exactly level. Preparation for installing a pre-formed pond linerĪlthough pre-formed liners save you some design decisions, they are hard work to install. Most liner manufacturers make waterfall sections to match their range.Ħ. These are straightforward to install with pre-formed liners, but it’s best to incorporate them at the same time as the main pond liner. Although topping up a pond is easy, making sure that the water quality is suitable is not so simple since tap water contains various impurities which can be toxic to fish and encourage algal growth.Īn alternative to a fountain is a waterfall. But do check the spread of the fountain, and make sure that the pond liner is large enough to catch the returning water, otherwise the pond level will drop dramatically. One simple and attractive way to move the water around is with a fountain. The sound of moving water is pleasant too, and adds to the pleasures of a pond. It’s also important to have some method of moving water around during still summer days to increase the oxygen content of the water. So take advice first before installing a pond which may turn out to be unsuitable. Of course, if you’re keen on stocking Koi, and big ones at that, you’ll have to design the pond with them in mind. The surface area should be large enough for plenty of oxygen to dissolve in the water, which will keep fish happy. A pre-formed pond liner suitable for fish Dirt and sediment will rest upon the rocks, becoming less noticeable.ĭecorate with rocks, bridge, aquatic plants, lighting, fountains, or whatever your imagination decides!Ĭombine two or more ponds for a larger, more dramatic presentation. If you got dirt in the pond while backfilling, it is a good idea to drain the pond completely, wipe clean (never use detergents) and refill with water.Ī layer of washed, lightly colored stone (pea gravel, cobblestones) may be arranged within the pond prior to stocking. If you are adding fish, you need to dechlorinate the water by using Ammo Lock 2 before adding fish. If water is chlorinated, allow 48 hours before adding plants. Gauge your time so the filling of water and backfilling of sand steps are finished at the same time. Commence filling with water slowly and continue backfilling with loose sand. Backfill with loose dirt or sand between pond and excavation, stopping at halfway mark between excavation base and pond's flange (upper lip). You should have the pond's edge slightly above ground level so the dirt around it slopes at least 10% away from the pond to prevent rain from washing soil, lawn fertilizers, etc. Bed the pond on a layer of sand, then level the pond. Rinse out pre-formed pond with water real well before installing.Ĥ. NOTE: For our molded shelf ponds, simply replicate the pond's contour within the excavation, making sure to fully support the shelf with tightly packed sand or dirt. 2" of play sand base under the pond and have some for around the edges. Take out any rocks, roots, or sharp debris. Make sure the excava- tion has a firmly compacted base. Dig a corresponding hole a little larger and deeper than the pond. You can outline it with chalk dust as well.ģ. Standing inside the pond, mark the pond's perimeter on the ground, using an edger or flat shovel. Select an area that is sunny and has at least 4-6 hours of sunlight.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |